日本SMC氣動位置傳感器[產品打印頁面]

]資料

點擊看大圖

如果您對該產品感興趣的話,可以

產品名稱: 日本SMC氣動位置傳感器
產品型號: -
產品展商: SMC
簡單介紹
日本SMC氣動位置傳感器 3。在2個位置安裝支架聯合（ISA-3-A）。注）進行的螺絲臨時收緊。 4。確認現有交換機的SUP口的凹槽已密封的連接增設車站。

日本SMC氣動位置傳感器的詳細介紹

日本SMC氣動位置傳感器
1. Mount the seal conduit on the terminal box. For mounting
procedure, refer to the catalog and instruction manual provided
by the manufacturer of the seal conduit.
2. Thread the cable through the seal conduit and arrange wiring
according to the polarity of the terminal block illustrated above.
3. Fasten the seal conduit with a tightening torque not greater
than 5 N??m. Do not hold the terminal box or the switch.
The detection distance is set with the LED level meter and setting
Keep the setting dial pulled out while in use. If released, it will
return to its original position and become unable to rotate.
1. For accuracy in setting, apply a clearance gauge to the detection
nozzle to replicate the set condition in advance.
2. Confirm that the set pressure is applied. If the setting dial is
fully open, the LED level meter appears as .
3. Pull the setting dial and rotate it in the positive direction. The
Throttle setting for blowing to prevent water and cutting oil from
(Clockwise: Close throttle; Counterclockwise: Open throttle)
∗ The setting is not applicable to valves without throttle.
2. Rotate the throttle clockwise for adjustment so that the
detection nozzle will not suck up water or cutting oil.
3. Power on the valve, then off again.
Confirm that the detection nozzle does not suck up water
Note) Do not rotate the throttle more than 5 turns or it will fall
4. The sensor output comes on when the lights on the LED level
meter turn on as . Complete the setting when this condition
5. Apply the clearance gauge again to confirm that the lights turn
2. Setting the installation needle
The installation needle should be moved by the fingertip.
Set the 2 green installation needles at the maximum and
minimum limits of pressure.
After setting the installation needles, locate the OPEN
arrow at the top right position and insert the claws on the
cover into the grooves on the case (indicated by in the
expanded view of A part). Rotate the cover clockwise until
it stops. Confirm that the cover is firmly secured.

產品留言

標題

聯系人

聯系電話

內容

驗證碼

點擊換一張

注：1.可以使用快捷鍵Alt+S或Ctrl+Enter發送信息!
2.如有必要,請您留下您的詳細聯系方式!

相關產品

SMC磁性開關安裝尺寸 D-Z73
SMC流量開關PF3A801H-L2Q適用流體空氣 CDQ2B32TF-25DZ
SMC水用數字式流量開關PF3W711-10-A-M
運作原理SMC數量式流量開關 PFMB7501-04-AW-R
SMC流量開關驅動方式 PFMB7102-04-D

SMC磁性開關安裝尺寸 D-Z73

SMC流量開關PF3A801H-L2Q適用流體空氣 CDQ2B32TF-25DZ

SMC水用數字式流量開關PF3W711-10-A-M

運作原理SMC數量式流量開關 PFMB7501-04-AW-R

SMC流量開關驅動方式 PFMB7102-04-D

名稱：上海乾拓貿易有限公司
上海地址：上海市嘉定區嘉涌路99弄6號713室

聯系人：羅丹
QQ：2880626082
直線電話：021-39526590
聯系人： 18917038407（同微信）
郵箱：[email protected]

聯系人;沈雪
企業QQ:2880626081
手機；18918574312（微信）
電話；021-69000975
郵箱:[email protected]

聯系人：章瑩玲
企業QQ:2880626085
手機；18918572467（微信）
電話；021-69000973
郵箱:[email protected]

聯系人：王亞波
QQ:2880626088
021-39529839-8012
手機：17321056802（同微信）
郵箱:[email protected]