BURKERT2002型角座閥，002133
電話：O21-3952 9829/3O-8O1O
傳真：O21-6O83 1959
手機：189 1857 2467
Q：125 5O9 6653
聯系人：張海情
郵箱：[email protected]
公司網址：www.yznetworks.com
二位二通角座閥，
緊湊的閥體，
媒體到+180°C，DN13-65
•超緊湊型，短
面到端面的長度
•使用壽命長
閥體青銅
不銹鋼
•交付FL OW方向
低于或高于座椅
氣動操作的兩位兩通閥**作
的活塞致動器。
致動器可以在兩種不同的材料，
取決于環境溫度。該標準
高環境溫度下的材料是PA
（如：外部**）PPS可用于溫度
實現了至140ºC.High的流率
與青銅色或不銹鋼2路身體
很短的面對面的長度。兼容
鍵入0251。
提供可靠的自調整填料壓蓋
高密封完整性。這些免維護，
強大的閥可以retrofi的翻版提供**的
一系列的配件，位置指示，中風
限制或手動操作。
類別2002可以結合...
技術數據流動方向閥座下面（氣體和液體）
Orifi CE DN 13 - 65
閥體材料青銅，鑄不銹鋼
執行器材料PA和PPS
PTFE密封材料（NBR，F(xiàn)PM，EPDM應要求提供）
介質水，酒精，油類，燃料，鹽溶液，液壓佛羅里達州的uid
堿性溶液，蒸汽，有機溶液
粘度。 600 mm2 / s的
填料壓蓋
（用硅脂）
彈簧補償?shù)腜TFE V形環
介質溫度）-10?+180°C，PTFE密封
環境溫度
PA actuator1）
PPS執行器
執行機構的尺寸Ø40-80
執行機構的尺寸Ø100-125
-10到+60°C
+5至+140°C
+5到+90°C，（brieflŸ至140ºC）
面對面寶得類型的長度為0251
安裝，根據需要，優選處于直立的位置的致動器
控制介質的中性氣體，空氣
。先導壓力
執行機構尺寸Ø40 - 80
執行機構尺寸Ø100
執行機構尺寸Ø100
執行機構尺寸直徑125
PA / PPS 10巴
PA 10酒吧
PPS 7欄
PA / PPS 7欄
端口連接G 3/8到G 2 1/2（“不擴散核武器條約”的要求）
類型6519
NAMUR
流量
Kv值水[立方米/小時]
測量在+20ºC，1巴的壓力閥
進口和自由出口
壓力值[巴]壓力表的壓力相對于現行
大氣壓力
1）注意：對于PA驅動器的尺寸為40，50和63，
的組合。介質溫度和。
環境溫度在下面的圖表所示
BURKERT2002型角座閥，002133
2/2-way Angle-Seat Valve,
compact valve body,
for media up to +180 °C, DN13-65
• Ultra compact version, short
face-to-face length
• Long service life
• Valve body in gunmetal and
stainless steel
• Deliverable with fl ow direction
below or above seat
operated
with a piston actuator.
The actuator is available in two different materials,
depending on the ambient temperature. The standard
material is PA for high ambient temperatures
(e.g. external sterilization) PPS is available for temperatures
up to 140ºC.High fl ow rates are attained
with the gunmetal or stainless steel 2-way body with
a short face-to-face length. Compatible with the
Type 0251.
The reliable self-adjusting packing gland provides
high sealing integrity. These maintenance-free and
robust valves can be retrofi tted with a comprehensive
range of accessories for position indication, stroke
limitation or manual override.
Type 2002 can be combined with...
Technical data Flow direction below seat (for gases and fluids)
Orifi ce DN 13 - 65
Body materials Gunmetal, cast stainless steel 316L
Actuator material PA or PPS
Seal material PTFE (NBR, FPM and EPDM on request)
Media Water, alcohol, oils, fuels, salt solutions, hydraulic fl uids
alkaline solutions, steam, organic solutions
Viscosity Max. 600 mm2/s
Packing gland
(with silicone grease )
PTFE V-rings with spring compensation
Media temperature1) -10 to +180 °C with PTFE seal
Ambient temperature
PA actuator1)
PPS actuator
Actuator sizes Ø 40-80
Actuator sizes Ø 100-125
-10 to +60 °C
+5 to +140 °C
+5 to +90 °C, (briefl y up to 140º C)
Face-to-face length As Bürkert Type 0251
Installation As required, preferably with actuator in upright position
Control medium Neutral gases, air
Max. pilot pressure
Actuator size Ø 40 - 80
Actuator size Ø 100
Actuator size Ø 100
Actuator size Ø 125
PA/PPS 10 bar
PA 10 bar
PPS 7 bar
PA/PPS 7 bar
Port connections G 3/8 to G 2 1/2 (NPT on request)
Type 6519
NAMUR
Flow rate
Kv-value Water [m3/h]
Measured at +20 ºC, 1 bar pressure at valve
inlet and free outlet
Pressure values [bar] Gauge pressures with respect to the prevailing
atmosphere pressure
1)Note: For PA actuators in the sizes 40, 50 and 63,
the combination of max. media temperature and max.
ambient temperature is as shown in the following chart:
BURKERT2002型角座閥，002133
